Music tools
Music tool guide and audio examples
Try an example recording
Level Up · 130 BPM Coastline · 98 BPM Paper Planets · 82 BPM
Go deeper
Before and after: what changes
Start with what you need to learn or make from your recording. The same track can go from a tempo estimate to a chord chart, a practice loop or notes that you can edit in a DAW. Each tool has a different job, and you can switch tools as the next question becomes clear.
- Timing
- A tempo estimate turns a steady pulse into a BPM you can use to set a project grid. Try the metronome over the recording for a few bars. If it walks away from the track, inspect where the pulse changes or count a shorter section by hand.
- Harmony
- A key estimate gives you a tonal center for the recording. The chord finder gives you time ranges so you can see where the harmony changes. Use the key to choose a starting scale, then listen to chord changes under a bass line or melody.
- Editable material
- Audio to MIDI turns audible pitches into editable note events. The new file carries timing and pitch information. Choose an instrument after importing it into your DAW, then repair any missed notes and adjust the rhythm before arranging a full part.
Recordings that give clearer results
Works well
- A recording with a clear drum pulse and several uninterrupted bars gives the BPM finder enough evidence to distinguish the beat from faster subdivisions.
- A sustained musical phrase with a clear bass line gives the key finder and chord finder useful context about the tonal center and the changes around it.
- A clean melody played by one instrument makes note boundaries easier to hear and MIDI events easier to check against the recording.
Avoid
- Speech, applause or a long quiet introduction can dominate a short clip. Start with a section where the music is audible and the beat has settled.
- A noisy rehearsal with several melodies at once can hide the pitch you want. Export the part you are practicing or use a clean excerpt when you have one.
- A click count from just one or two taps can vary widely with your timing. Tap through several bars and compare the result with what you hear.
Step by step
- Pick the output you needUse Song Analyzer for a first pass over an unfamiliar track. Pick a focused tool if your question is already specific, such as checking the key, finding the pace or mapping a melody.
- Cross-check the first estimateRun the tempo or harmony checks on the same section. Try Tap Tempo if the automatic result feels like half or twice the speed you hear.
- Practice a section at a comfortable paceOpen the speed and pitch changer when you need to slow down a recording or move it into a comfortable singing range. Choose a short range and check the line before changing the entire track.
- Take notes into another sessionExport MIDI when you need editable notes, or keep the report beside your session when you are checking tempo and harmony. Compare it with the source during the first playback.
How the tools arrive at a result
- Pulse and subdivisions
- A song can support two readable tempo grids. A groove counted at seventy beats per minute may also be counted at one hundred and forty if the faster subdivision feels like the beat. Choose the grid that makes the musical phrases easy to count.
- Keys and chord boundaries
- An estimate is strongest when notes consistently point to one tonal center. Solo breaks, borrowed chords and key changes can produce different answers across sections. A chord timestamp helps you hear that distinction in the recording.
- Lyric phrasing
- Use Lyrics Generator when you need draft lines to sing or edit. Read each line against the intended beat and trim extra syllables where the vocal has little room. Keep a chorus line you want to reuse when asking for another draft.
More questions
Which music tool should I open first?
Open Song Analyzer if you have a track and want an overview. Open Tap Tempo or the metronome if you only need a beat reference.
Can two BPM estimates both be useful?
Yes. One may follow the larger pulse and the other its subdivision. Count several phrases or play a click alongside the track to see which grid matches your arrangement.
Why doesn't the chord chart reach the beginning of my recording?
A spoken or percussion-only introduction may have no reliable chord. Listen for the entry of the pitched instruments, then use the first stable label as a starting point.
What should I check after exporting MIDI?
Listen for missing attacks, overly long notes and extra pitches. Fix those events in the piano roll before layering a new instrument over the exported part.
Can I compare the tools without bringing my own track?
Yes. Play the three example songs on this page, then open Song Analyzer or one of the focused audio tools and choose its example from the sample list.